From Interlock Rochester Wiki
(Difference between revisions)
|
|
| Line 1: |
Line 1: |
| - | acceleration = 0
| + | |
| - | bed_temperature = 0
| + | |
| - | bottom_layer_speed_ratio = 0.3
| + | |
| - | bridge_fan_speed = 100
| + | |
| - | bridge_flow_ratio = 1
| + | |
| - | bridge_speed = 60
| + | |
| - | cooling = 0
| + | |
| - | disable_fan_first_layers = 1
| + | |
| - | duplicate_distance = 6
| + | |
| - | duplicate_x = 1
| + | |
| - | duplicate_y = 1
| + | |
| - | end_gcode = M104 S0 ; turn off hot end\nM140 S0 ; turn off bed\nG0 X0 Y144 ; present the print\nM84 ; disable motors
| + | |
| - | extrusion_axis = E
| + | |
| - | extrusion_multiplier = .99
| + | |
| - | extrusion_width_ratio = 0
| + | |
| - | fan_always_on = 0
| + | |
| - | fan_below_layer_time = 60
| + | |
| - | filament_diameter = 1.75
| + | |
| - | fill_angle = 45
| + | |
| - | fill_density = 0.25
| + | |
| - | fill_pattern = rectilinear
| + | |
| - | first_layer_bed_temperature = 0
| + | |
| - | first_layer_height_ratio = 1
| + | |
| - | first_layer_temperature = 200
| + | |
| - | g0 = 0
| + | |
| - | gcode_arcs = 0
| + | |
| - | gcode_comments = 0
| + | |
| - | gcode_flavor = reprap
| + | |
| - | infill_acceleration = 50
| + | |
| - | infill_every_layers = 1
| + | |
| - | infill_speed = 80
| + | |
| - | layer_height = 0.3
| + | |
| - | max_fan_speed = 100
| + | |
| - | min_fan_speed = 35
| + | |
| - | min_print_speed = 10
| + | |
| - | notes =
| + | |
| - | nozzle_diameter = 0.5
| + | |
| - | output_filename_format = [input_filename_base].g
| + | |
| - | perimeter_acceleration = 25
| + | |
| - | perimeter_speed = 30
| + | |
| - | perimeters = 3
| + | |
| - | post_process =
| + | |
| - | print_center = 72,72
| + | |
| - | retract_before_travel = 2
| + | |
| - | retract_length = 3
| + | |
| - | retract_lift = 0
| + | |
| - | retract_restart_extra = 0
| + | |
| - | retract_speed = 30
| + | |
| - | rotate = 0
| + | |
| - | scale = 1
| + | |
| - | skirt_distance = 6
| + | |
| - | skirt_height = 1
| + | |
| - | skirts = 1
| + | |
| - | slowdown_below_layer_time = 15
| + | |
| - | small_perimeter_speed = 30
| + | |
| - | solid_fill_pattern = rectilinear
| + | |
| - | solid_infill_speed = 60
| + | |
| - | solid_layers = 3
| + | |
| - | start_gcode = G28 ; home all axes
| + | |
| - | support_material = 0
| + | |
| - | support_material_tool = 0
| + | |
| - | temperature = 180
| + | |
| - | travel_speed = 150
| + | |
| - | use_relative_e_distances = 1
| + | |
| - | z_offset = 0
| + | |
Latest revision as of 13:01, 26 March 2012
